In2Bones Launches CoLink Vallux™ Active Bunion Procedure

Multi-directional, No Fusion Correction Speeds and Simplifies Bunion Surgeries

MEMPHIS, Tenn.--(BUSINESS WIRE)--#bunion--In2Bones Global, Inc. today announces the commercial launch of the CoLink Vallux™ Active Bunion, a new, minimally invasive, joint-sparing correction technique for moderate to severe bunions.

The Active Bunion implant and guided translational osteotomy technique improve on traditional open fixation approaches as well as newer bunion surgeries by providing surgeons with a simpler, faster procedure that doesn’t violate the joint or require a 1^st Tarsometatarsal joint fusion.

The implant consists of a zero-prominence CoLink Vallux™ plate and a choice of non-locking and variable angle locking screws for enhanced angular stability, together with a full instrument set.

Using this new, minimally invasive procedure, surgeons can correct joint alignment in multiple dimensions while avoiding any restriction of the joint space and not fusing the joint at the midfoot. The result is total range of motion preservation and superior cosmesis via a much smaller incision of 1-2 cm, compared with the larger incision required for Chevron osteotomy (5-7 cm).

For the patient, the Active Bunion’s smaller incision and technique as a whole reduces internal scarring compared with other bunion corrections, decreasing the typical postoperative stiffness, pain, and potential for wound complications.

"Patients prefer the smallest possible incision, and they do not want a fused joint unless absolutely necessary,” explains Jon Simon, Executvie Vice President of Commerical at In2Bones. “The CoLink Vallux Active Bunion fulfills both of these patient demands.”

An Evolved Surgery with More Surgeon and Patient Benefits

With greater simplicity comes shorter OR time. The Active Bunion procedure can typically be completed in about 20 minutes, compared to 40-60 minutes plus for other more invasive and complex corrections. Recovery can also be shorter than traditional bunion surgeries. With no joint violation, which preserves the total range of motion, patients may return to weight-bearing activity sooner, with less physical therapy.

The Active Bunion’s evolved technique, technology, and fixation solution is intended to address over 90 percent of bunion cases. Compare it to other established hallux valgus procedures:

Lapidus – Unlike this end-stage procedure, the Active Bunion’s simpler, quicker guided implant technique cuts down on multiple surgical steps, thereby decreasing OR time. It spares the midfoot joint from fusion, with early weight-bearing, improved cosmesis, and fewer overall complications.

Percutaneous Screw Fixation – Compared to the blind resection and steep learning curve required for the Burr osteotomy, the Active Bunion procedure is reproducible and straightforward. The guided osteotomy reduces the risk of shortening or necrosis.

IM Blade Plates – Eliminating multiple surgical steps common to this technique, the Active Bunion procedure allows surgeons to dictate placement while the implant provides greater strength and stability through two distal and proximal screws instead of the customary single screw.

Like all other products in In2Bones’ extensive platform of single-use implants for the hand and foot, the CoLink Vallux™ Active Bunion system is packaged sterile for traceability and patient safety.

For more information about this implant or other In2Bones Global extremity products, please visit www.In2Bones.com.

About In2Bones

Headquartered in Memphis, Tennessee, In2Bones is a global designer, manufacturer and distributor of medical devices for the treatment of disorders and injuries of the upper (hand, wrist, elbow) and lower (foot and ankle) extremities. For more information, visit www.i2b-usa.com.

Safe-Harbor Statement:

This press release contains “forward-looking statements” within the meaning of Section 27A of the Securities Act of 1933, as amended, and Section 21E of the Securities Exchange Act of 1934, as amended. All statements made in this press release, other than statements of historical fact, are forward-looking statements. Forward-looking statements reflect management’s current view of future performance, results, and trends and may be identified by their use of terms such as “anticipate,” “believe,” “could,” “estimate,” “expect,” “intend,” “may,” “plan,” “predict,” “will,” and other similar terms. The company wishes to caution readers that actual results might differ materially from those described in the forward-looking statements. Forward-looking statements are subject to a number of risks and uncertainties impacting the business, including increased competition, technical obsolescence, regulatory issues, general economic conditions and other risks.

Media Contacts:
Jon Simon | Executive Vice President of Commercial
In2Bones USA
6000 Poplar Ave, Suite 115 Memphis, TN 38119
O: 901.260.7931 • F: 844-712-6637
Email: jsimon@i2b-usa.com

Or:

Bob Reed
Element-R Partners
O: 630.579.1770
Email: bob@rurelevant.com